revset: stop serializing node when using "%ln" Turning hundred of thousand of node from node to hex and back can be slow… what about we stop doing it? In many case were we are using node id we should be using revision id. However this is not a good reason to have a stupidly slow implementation of "%ln". This caught my attention again because the phase discovery during push make an extensive use of "%ln" or huge set. In absolute, that phase discovery probably should use "%ld" and need to improves its algorithmic complexity, but improving "%ln" seems simple and long overdue. This greatly speeds up `hg push` on repository with many drafts. Here are some relevant poulpe benchmarks: ### data-env-vars.name = mozilla-try-2023-03-22-zstd-sparse-revlog # benchmark.name = hg.command.push # bin-env-vars.hg.flavor = default # bin-env-vars.hg.py-re2-module = default # benchmark.variants.explicit-rev = all-out-heads # benchmark.variants.issue6528 = disabled # benchmark.variants.protocol = ssh # benchmark.variants.reuse-external-delta-parent = default ## benchmark.variants.revs = any-1-extra-rev before: 44.235070 after: 20.416329 (-53.85%, -23.82) ## benchmark.variants.revs = any-100-extra-rev before: 49.234697 after: 26.519829 (-46.14%, -22.71) ### benchmark.name = hg.command.bundle # bin-env-vars.hg.flavor = default # bin-env-vars.hg.py-re2-module = default # benchmark.variants.revs = all # benchmark.variants.type = none-streamv2 ## data-env-vars.name = heptapod-public-2024-03-25-zstd-sparse-revlog before: 10.138396 after: 7.750458 (-23.55%, -2.39) ## data-env-vars.name = mercurial-public-2024-03-22-zstd-sparse-revlog before: 1.263859 after: 0.700229 (-44.60%, -0.56) ## data-env-vars.name = mozilla-try-2023-03-22-zstd-sparse-revlog before: 399.484481 after: 346.5089 (-13.26%, -52.98) ## data-env-vars.name = pypy-2024-03-22-zstd-sparse-revlog before: 4.540080 after: 3.401700 (-25.07%, -1.14) ## data-env-vars.name = tryton-public-2024-03-22-zstd-sparse-revlog before: 2.975765 after: 1.870798 (-37.13%, -1.10)

# Support code for event tracing in Mercurial. Lives in demandimport
# so it can also be used in demandimport.
#
# Copyright 2018 Google LLC.
#
# This software may be used and distributed according to the terms of the
# GNU General Public License version 2 or any later version.

import contextlib
import os

_pipe = None
_checked = False
_session = 'none'


def _isactive():
    global _pipe, _session, _checked
    if _pipe is None:
        if _checked:
            return False
        _checked = True
        if 'HGCATAPULTSERVERPIPE' not in os.environ:
            return False
        _pipe = open(os.environ['HGCATAPULTSERVERPIPE'], 'w', 1)
        _session = os.environ.get('HGCATAPULTSESSION', 'none')
    return True


@contextlib.contextmanager
def log(whencefmt, *whenceargs):
    if not _isactive():
        yield
        return
    whence = whencefmt % whenceargs
    try:
        # Both writes to the pipe are wrapped in try/except to ignore
        # errors, as we can see mysterious errors in here if the pager
        # is active. Presumably other conditions could trigger
        # problems too.
        try:
            _pipe.write('START %s %s\n' % (_session, whence))
        except IOError:
            pass
        yield
    finally:
        try:
            _pipe.write('END %s %s\n' % (_session, whence))
        except IOError:
            pass


def counter(label, amount, *labelargs):
    if not _isactive():
        return
    l = label % labelargs
    # See above in log() for why this is in a try/except.
    try:
        _pipe.write('COUNTER %s %d %s\n' % (_session, amount, l))
    except IOError:
        pass